The technologies of audio – both old and new – can often trip up the average listener who just wants to plug their stuff in and listen to music. With the resurgence in interest in vinyl, some old-school technical problems that most people have never had to deal with are suddenly back to annoy us and get between us and our music.

 

There are two commonly asked questions when it comes to turntables: Do I need a phono pre-amp? and Why do I need a phono pre-amp?  The answer to the former is yes and the answer to the latter is (as usual) complicated.

 

Basically, you need some sort of phono pre-amp (sometimes referred to as a phono stage) because the output signal developed by your turntable isn’t strong enough for your amplifier/receiver’s inputs. Your amplifier needs a certain level of voltage to “turn on” or start working. A low signal level will also often  result in more noise being amplified than signal.

 

Generally speaking, a line-level input is around 44mV peak amplitude and 33mV RMS. This is measured in DbV and would translate to -10DbV, but we’ll leave the why’s and how’s of that measurement for another post. Your CD player, streaming device, DVD player, etc., all output to this standard. The problem is the voltage generated by the tiny magnet on your turntable’s cartridge isn’t anywhere near the minimum live-level. To compensate you need an extra stage of amplification before you can get to the pre-amp in your receiver.

 

There are two types of phono cartridge, and without debating the merits or minuses of either let’s just look at the raw facts.

 

 

Moving Coil Cartridge (MC)

The MC cartridge has two coils attached to the stylus (one for each stereo channel). Those two coils of wire oscillate inside a fixed magnet and it’s the movement between the coils and the magnet that generates the electrical audio signal. But because the wires and magnet are so small the voltage generated is typically only around 1.5mV peak.

 

 

Moving Magnet Cartridge (MM)

The MM cartridge has two magnets attached to the stylus (one for each stereo channel) that oscillates between two fixed coils of wire. As with the MC cartridge, it’s the oscillation between the coil and magnet that develops the electrical audio signal. The typical peak voltage developed by a MM cartridge is around 3 to 5mV. This results in an overall gain in signal from source to output of around 38dB (60dB for MC cartridges).

 

 

Simply put, your phono pre-amp boosts the level of the signal using a simple transformer or amplifer circuit from the extremely small voltage level developed by the cartridge up to a level that your amplifier or receiver needs for its own pre-amp stage.

 

Because the MC cartridge develops less capacitance and inductance across the wires leading from the cartridge, Moving Coil cartridges are generally considered to offer a flatter audio response. The compromise is they also require more boost from the phono pre-amp which also brings noise issues into consideration.

 

All of this results in the need for an additional pre-amp stage. Some receivers have built in phono inputs to boost the signal electrically. Some turntables have built in phono pre-amps which allow you to connect the output of your turntable directly to a line-level input on your receiver or amp. But if neither your turntable nor receiver offers a phono pre-amp you’ll have to get an outboard pre-amp to connect between your turntable and receiver. These are generally active devices that use op-amps to boost the signal and filter noise.

 

There are resistance (and in some cases capacitance) settings on most decent quality phono pre-amps meant to change certain loading characteristics of the cartridge and coil that may affect your sound. There is no tried and true rule of thumb for resistance settings and your best bet is to experiment until you find a setting that sounds best to you. Some resistance settings will leave the output too low or too high and others will be barely noticeable. If your phono pre- has settings for capacitance these are meant to specifically alter or adjust the upper frequencies for variances in how the wires in the tone arm and turntable interact with the signal.

 

A Quick Note On Why Your Turntable May Need A Ground Wire

Generally speaking, turntables are electro-mechanical devices with little or no circuitry beyond the wiring for the cartridge. Many times the drive motor is isolated from the platter and tonearm assembly so it is easier and cheaper for a turntable manufacturer to leave it up to the end user to ground the tonearm assembly to the common ground used by the receiver or amplifier. For example, a belt driven turntable may have the motor drive designed as a completely separate assembly from the platter in order to lower rumble. A ground connection to the amplifier (and not the motor) becomes necessary to eliminate hum and other noise.

Here's avideo of a vinyl LP and some other mediums viewed with an electron microscope. Geek on!